Welcome to Boardsort™ - Learn - Sell - Profit -

Learn to properly Sort, Sell, and Profit from your electronic scrap material.
It is currently Fri Apr 26, 2024 6:25 pm


Post new topic Reply to topic  Page 1 of 1
  [ 6 posts ] 
  Previous topic | Next topic 
Author Message
Mistah420
 Post subject: Board id
PostPosted: Sun Nov 29, 2015 7:56 pm 

Joined: Fri Nov 20, 2015 9:17 pm
Posts: 14
Older boards


Attachments:
File comment: Back
IMG_20151129_165236.jpg
IMG_20151129_165236.jpg [ 2.52 MiB | Viewed 3626 times ]
File comment: Front
IMG_20151129_165109.jpg
IMG_20151129_165109.jpg [ 2.24 MiB | Viewed 3626 times ]
Top
 Profile  
 
lostinlodos
 Post subject: Re: Board id
PostPosted: Mon Nov 30, 2015 2:37 am 
Site Admin
User avatar

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 9764
Location: Low DOS
Top 6 peripheral more than likely
Bottom 3 are mid grade and low.
Top
 Profile  
 
Mistah420
 Post subject: Re: Board id
PostPosted: Mon Nov 30, 2015 3:50 am 

Joined: Fri Nov 20, 2015 9:17 pm
Posts: 14
What if some of the chip got stuck on the heatsink. What grade would the big board be. And can i throw that heatsink with my gold pins. I scratched it and it's a different color, so I'm guessing it's gold plated. And the little board I'm thinking peripheral. But not sure.


Attachments:
File comment: Front of smaller board.
IMG_20151130_002647.jpg
IMG_20151130_002647.jpg [ 2.5 MiB | Viewed 3607 times ]
File comment: Should I remove the metal from the bigger board that's attached to the connections
IMG_20151130_002541.jpg
IMG_20151130_002541.jpg [ 2.25 MiB | Viewed 3607 times ]
Top
 Profile  
 
lostinlodos
 Post subject: Re: Board id
PostPosted: Mon Nov 30, 2015 2:17 pm 
Site Admin
User avatar

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 9764
Location: Low DOS
The little one is going to be mid grade.
The large one us now peripheral without the cpu :/
The gigabyte heatsync is gold plated. But it's very thin. Gigabyte and AsRock use the same heatsync with a different print on it.

Put it in it's own spot in a bag in your shipment though since the cpu is still attached.
Normally those two heatsyncs would be between 60-80 cents a pound. i usually toss them in my gold connector bag.
Top
 Profile  
 
Mistah420
 Post subject: Re: Board id
PostPosted: Mon Nov 30, 2015 5:05 pm 

Joined: Fri Nov 20, 2015 9:17 pm
Posts: 14
Thanks for all the help.I'm getting ready to send in my first load. So I'm just trying to get it right. Definitely takes a lot of learning in the e-scrap game


Attachments:
File comment: Back of the 2 bottom ones
IMG_20151130_134239.jpg
IMG_20151130_134239.jpg [ 2.07 MiB | Viewed 3573 times ]
File comment: Can I put with my gold finger cards? Not to sure about the 2 bottom ones.
IMG_20151130_134100.jpg
IMG_20151130_134100.jpg [ 2.54 MiB | Viewed 3573 times ]
Top
 Profile  
 
lostinlodos
 Post subject: Re: Board id
PostPosted: Mon Nov 30, 2015 5:47 pm 
Site Admin
User avatar

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 9764
Location: Low DOS
Top pic mid on top peripheral below
Bottom pic. The riser card is backplane.
The wifi cards with the steel spreaders are peripheral. The ones without spreaders go telco. The gameboy card will be telco with one or two ics. You /may/ get ram if three ics.
The other cartridge card next to it is gold finger card.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 6 posts ] 

Board index » What is it? Identification Forum

All times are UTC - 5 hours [ DST ]

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: