Boardsort.com

Your complete E-scrap resource website. LEARN - SELL - PROFIT
It is currently Tue Sep 26, 2017 6:57 am


Post new topic Reply to topic  [ 9 posts ] 
Author Message
PostPosted: Thu Jun 23, 2016 9:31 am 

Joined: Tue Jun 14, 2016 1:34 pm
Posts: 13
These came from CRTs and Power Supplies. Are they something that Boardsort will take? And if so, what grade? Do I need to do anything else to break them down further?


Attachments:
Power Supply Board.jpg
Power Supply Board.jpg [ 1.57 MiB | Viewed 545 times ]
Power Supply Board (2).jpg
Power Supply Board (2).jpg [ 1.62 MiB | Viewed 545 times ]
CRT Boards (3).jpg
CRT Boards (3).jpg [ 1.57 MiB | Viewed 545 times ]
CRT Boards (2).jpg
CRT Boards (2).jpg [ 2.27 MiB | Viewed 545 times ]
CRT Boards (1).jpg
CRT Boards (1).jpg [ 1.68 MiB | Viewed 545 times ]
Top
 Profile  
 
PostPosted: Thu Jun 23, 2016 10:11 am 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3331
Location: Low DOS
They're all low grade. You can pull aluminium and copper for local as they're worth more than the boards.


Top
 Profile  
 
PostPosted: Thu Jun 23, 2016 3:39 pm 

Joined: Tue Jun 14, 2016 1:34 pm
Posts: 13
Pulling the aluminum and copper was fairly difficult on the one power supply I started with... do you have any ideas/suggestions for how to do this?


Top
 Profile  
 
PostPosted: Fri Jun 24, 2016 12:46 pm 

Joined: Tue Jun 03, 2014 2:15 pm
Posts: 84
pry off the ic chip on the bottom tv board...boardsort buys them by the pound


Top
 Profile  
 
PostPosted: Fri Jun 24, 2016 12:55 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3331
Location: Low DOS
I'll do a full and complete breakdown to bare board this weekend of a standard power supply and maybe a tv for my what's inside it.


Top
 Profile  
 
PostPosted: Fri Jun 24, 2016 3:10 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3331
Location: Low DOS
Yep got a tv so I'll post full breakdowns to bare boards this weekend.


Top
 Profile  
 
PostPosted: Mon Jun 27, 2016 12:16 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3331
Location: Low DOS
I'm a little behind schedule but they are on the list. ;)


Top
 Profile  
 
PostPosted: Tue Jun 28, 2016 9:57 pm 
Reputable Seller

Joined: Fri Jan 31, 2014 10:22 am
Posts: 746
Mike the Scrapper had done a video a year or two ago where he breaks down low grade boards for metal recovery. On most of what you have here, pliers and elbow grease will be your best tools. When I do low grade boards, I usually go for the transformers with the most weight or exposed copper. Exposed copper transformers then can be further broken down to recover the wire which can go as #2 copper.

_________________
kgryczan
Forum Moderator


Top
 Profile  
 
PostPosted: Tue Jun 28, 2016 10:08 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3331
Location: Low DOS
I've got the boards out. Pics within 24 hours.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 5 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

cron