Welcome to Boardsortâ„¢ - Learn - Sell - Profit -

Learn to properly Sort, Sell, and Profit from your electronic scrap material.
It is currently Tue Mar 19, 2024 2:02 am


Post new topic Reply to topic  [ 9 posts ] 
Author Message
PostPosted: Wed Sep 14, 2016 1:08 am 

Joined: Sun Aug 17, 2014 8:17 pm
Posts: 17
Hey all... Figured it would be easier to break this up into a couple of posts. Again, thanks very much!


Attachments:
File comment: SET#7: Does Chris buy these at all?
20160913_233647.jpg
20160913_233647.jpg [ 641.92 KiB | Viewed 7118 times ]
File comment: SET#6: These little doo-dads are found inside Ultrium tape cartridges. Tiny & thin, but appears to have gold wire... Thoughts?
20160913_233609.jpg
20160913_233609.jpg [ 685.66 KiB | Viewed 7118 times ]
File comment: SET#5: Front & back... IDE/USB storage modules... periph?
20160913_232946.jpg
20160913_232946.jpg [ 696.52 KiB | Viewed 7118 times ]
File comment: SET#4: Legs are half-and-half... Is this just solder?
20160913_232633.jpg
20160913_232633.jpg [ 652.2 KiB | Viewed 7118 times ]
File comment: SET#3: Back... More pins than grandma's pincushion lol
20160913_232602.jpg
20160913_232602.jpg [ 768.99 KiB | Viewed 7118 times ]
File comment: SET#3: Front... Lots of pins on a tiny board
20160913_232515.jpg
20160913_232515.jpg [ 698.89 KiB | Viewed 7118 times ]
File comment: SET#2: Back
20160913_232054.jpg
20160913_232054.jpg [ 782.8 KiB | Viewed 7118 times ]
File comment: SET#2: Front... Large socket perhaps?
20160913_232041.jpg
20160913_232041.jpg [ 1000.87 KiB | Viewed 7118 times ]
File comment: SET#1: Back
20160913_232017.jpg
20160913_232017.jpg [ 983.64 KiB | Viewed 7118 times ]
File comment: SET#1: Front... my guess is telco
20160913_232006.jpg
20160913_232006.jpg [ 911.75 KiB | Viewed 7118 times ]
Top
 Profile  
 
PostPosted: Wed Sep 14, 2016 1:36 am 
Site Admin
User avatar

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 9748
Location: Low DOS
Again... Tomorrow

_________________
42 6F 61 72 64 73 6F 72 74 2E 63 6F 6D


Top
 Profile  
 
PostPosted: Wed Sep 14, 2016 2:46 am 
Site Admin
User avatar

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 9748
Location: Low DOS
Set 7) SIM cards don't have a category on the quote system but are accepted.
You can send them in; just make note of it in the text box on the final page of the quote.
Memory cards that are without case can go telco. With case goes peripheral or remove the plastic case for telco.
Set 6) plated copper. Goes in peripheral
Set 5) early equivalent of solid state drives. The go telco in most cases.
Set 4) 8086/8088
Set 3) gold pin board. Send it in to get scanned for a quote. Again not on the list so make note in the text box on the final page
Set 2) large socket
Set 1) telco

_________________
42 6F 61 72 64 73 6F 72 74 2E 63 6F 6D


Top
 Profile  
 
PostPosted: Wed Sep 14, 2016 3:40 pm 

Joined: Fri Jul 01, 2016 6:55 pm
Posts: 742
Location: Texas
Lost,

On set 3: why would that not be considered a back plane? Is it because of the silver pins?

On set 2: I may say this wrong.....I realize that's a slotted mb, but with the amount of ic's what keeps it from going telco?


Top
 Profile  
 
PostPosted: Wed Sep 14, 2016 3:46 pm 

Joined: Fri Jan 31, 2014 12:53 pm
Posts: 467
you might get gold cap chips board for that 'set 2' mother board... you have a single gold cap chip soldered to it, so i believe if you ask them you will clear it. otherwise, yes it would be large socket motherboard... thats just what they classify the old x286/x386 socket boards.


Top
 Profile  
 
PostPosted: Wed Sep 14, 2016 5:31 pm 
Site Admin
User avatar

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 9748
Location: Low DOS
On two ; I was hesitant to say gold cap board but I'll defer to MLS for experience, I've never had a single cap CPU board to send in.
There's a weight vs materials offset on pre 386 boards. It's just how they classify them. Some do make telco but this one
Actually with the single gold cap you may get telco for this one, which is more likely in my guess than gold cap, but again until it gets there we're all guessing. ;)


Pin board is worth more than backplane. That server port is large enough to class it separately on such a small adapter board.

_________________
42 6F 61 72 64 73 6F 72 74 2E 63 6F 6D


Top
 Profile  
 
PostPosted: Wed Sep 14, 2016 9:29 pm 

Joined: Fri Jul 01, 2016 6:55 pm
Posts: 742
Location: Texas
Well I kinda understand about the mb.
Im a little confused about the pin board......what makes it a pin board?
I went back an looked at the pictures again and realized the front of that board is nearly all pins. Is it because the amount of pins covering covering the board?


Top
 Profile  
 
PostPosted: Thu Sep 15, 2016 2:03 am 
Site Admin
User avatar

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 9748
Location: Low DOS
You've got it exactly. One side is almost entirely pins.

_________________
42 6F 61 72 64 73 6F 72 74 2E 63 6F 6D


Top
 Profile  
 
PostPosted: Thu Sep 15, 2016 5:43 pm 

Joined: Fri Jul 01, 2016 6:55 pm
Posts: 742
Location: Texas
Thanks Lost.....I appreciate all your help.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 5 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: