Boardsort.com

Your complete E-scrap resource website. LEARN - SELL - PROFIT
It is currently Sun Dec 17, 2017 2:06 am


Post new topic Reply to topic  [ 11 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Help With ID
PostPosted: Tue Oct 18, 2016 10:26 pm 

Joined: Wed May 20, 2015 4:31 pm
Posts: 31
see attached:

4 and 5 are front and back


Attachments:
20161018_213419.jpg
20161018_213419.jpg [ 4.27 MiB | Viewed 1165 times ]
Top
 Profile  
 
 Post subject: Re: Help With ID
PostPosted: Tue Oct 18, 2016 11:05 pm 

Joined: Fri Jul 01, 2016 6:55 pm
Posts: 201
Location: Texas
1 & 2 I'm not sure....small socket maybe?
3 gold finger
4 & 5 are peripheral


Top
 Profile  
 
 Post subject: Re: Help With ID
PostPosted: Tue Oct 18, 2016 11:11 pm 

Joined: Wed May 20, 2015 4:31 pm
Posts: 31
I was hoping 1 and 2 slot processor trying to figure out what is slot proc


Top
 Profile  
 
 Post subject: Re: Help With ID
PostPosted: Wed Oct 19, 2016 1:33 am 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3588
Location: Low DOS
1 & 2are probably gold finger card but possibly telco. It's straddling that line.

This is one for MLS. I'm not totally sure.

_________________
-- my grades are my own and do not represent an offer from boardsort, nor are they guaranteed. Please keep that in mind.


Top
 Profile  
 
 Post subject: Re: Help With ID
PostPosted: Wed Oct 19, 2016 10:01 am 

Joined: Fri Jan 31, 2014 12:53 pm
Posts: 436
cards like 1&2 have gone as gold finger cards for me in the past... I have been meaning to ask them about them though, because the are well populated and have good surface mounted devices. I plan on heading up there tomorrow or friday and if i remember to ask, I will let you all know.


Top
 Profile  
 
 Post subject: Re: Help With ID
PostPosted: Wed Oct 19, 2016 12:36 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3588
Location: Low DOS
My best guess is 1 is finger and 2 with the nice fibre chip would push into telco.
But let's let MLS ask on Friday and we'll know for sure.

_________________
-- my grades are my own and do not represent an offer from boardsort, nor are they guaranteed. Please keep that in mind.


Top
 Profile  
 
 Post subject: Re: Help With ID
PostPosted: Thu Oct 20, 2016 6:42 pm 

Joined: Fri Jan 31, 2014 12:53 pm
Posts: 436
confirmed the cards go as gold finger.


Top
 Profile  
 
 Post subject: Re: Help With ID
PostPosted: Fri Oct 21, 2016 7:36 am 

Joined: Wed May 20, 2015 4:31 pm
Posts: 31
Thank you all


Top
 Profile  
 
 Post subject: Re: Help With ID
PostPosted: Thu Oct 27, 2016 5:39 am 

Joined: Mon Dec 29, 2014 1:19 pm
Posts: 10
Location: mississippi
mcm262 wrote:
I was hoping 1 and 2 slot processor trying to figure out what is slot proc

Slot processors, best example, Pentium and Pentium 2, in short they are CPUs' that are installed on a mother board via a slot, like ram but larger. They will have gold fingers, a plastic case on one side and a large heat sink on the other.

link
https://en.wikipedia.org/wiki/Pentium_II


Top
 Profile  
 
 Post subject: Re: Help With ID
PostPosted: Thu Oct 27, 2016 1:23 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3588
Location: Low DOS
Good example
Any slot 1 slot 2 slot a CPU
Most via slot v CPUs

Via slot processors look like like intel xeon CPUs

Slot processors were an attempt to standardise a way to make interchangeable extensions to compatible motherboards without needing a new mobo. Such as adding USB controllers or adding ata support to ide boards.
In intels case adding mmx extensions
AMD added sas extensions on ide for use with a proprietary breakout; and mmc via CPU the first CPU supported accelerated graphics
Via used two slots, one for a CPU and one was a coprocessor board.

Dual slot boards utilise a termination board that is of identical size and shape but only has a single 12 pin IC and hundreds of CMCs. These go as telco.

Easiest classification along with the Wikipedia photo and gallery photos is
A slot processors will always have one big giant CPU. It will usually have one or to smaller square CPUs. Coprocessor units. It will always have CMCs. They are thicker and heavier than standard than common expansion cards. They have a layered two tier finger layout
And they are always gold sandwich boards. You can see three layers by looking at the side edge of the card.

_________________
-- my grades are my own and do not represent an offer from boardsort, nor are they guaranteed. Please keep that in mind.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: