Boardsort.com

Your complete E-scrap resource website. LEARN - SELL - PROFIT
It is currently Fri Jun 23, 2017 4:25 am


Post new topic Reply to topic  [ 9 posts ] 
Author Message
PostPosted: Mon Jan 23, 2017 10:51 pm 

Joined: Sun Jan 08, 2017 4:44 pm
Posts: 12
Please just put the card to the board type.


Attachments:
DSC01386.JPG
DSC01386.JPG [ 2.88 MiB | Viewed 636 times ]
DSC01385.JPG
DSC01385.JPG [ 2.91 MiB | Viewed 636 times ]
DSC01384.JPG
DSC01384.JPG [ 2.84 MiB | Viewed 636 times ]
DSC01370.JPG
DSC01370.JPG [ 2.57 MiB | Viewed 636 times ]
DSC01369.JPG
DSC01369.JPG [ 2.93 MiB | Viewed 636 times ]
Top
 Profile  
 
PostPosted: Mon Jan 23, 2017 11:18 pm 

Joined: Sun Jan 08, 2017 4:44 pm
Posts: 12
If I remove the removable IC chips and Eproms from the sockets of boards 6, 8, and 9 of spades will it down grade the boards and if so to what grade. Also if I just only take a couple IC/Eproms off of each of these boards would the grade stay the same?


Top
 Profile  
 
PostPosted: Mon Jan 23, 2017 11:27 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3062
Location: Low DOS
9)peripheral remove Dallas box
8)telco remove Dallas boxes
6)peripheral
3)large socket remove pentium and send separate
Snip the battery loose CAREFULLY, below the isa ports.
2)large socket

_________________
-- my grades are my own and do not represent an offer from boardsort, nor are they guaranteed. Please keep that in mind.


Top
 Profile  
 
PostPosted: Mon Jan 23, 2017 11:30 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3062
Location: Low DOS
9 remove ICs peripheral either way
8 no touch (leave ICs in)
6 no touch, your probably at midgrade without the 924s

_________________
-- my grades are my own and do not represent an offer from boardsort, nor are they guaranteed. Please keep that in mind.


Top
 Profile  
 
PostPosted: Mon Jan 23, 2017 11:34 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3062
Location: Low DOS
Hey MLS; can you spy what's missing on the soc7 board?
Hint not the second socket 7

Bonus points if you can say why it's missing.

_________________
-- my grades are my own and do not represent an offer from boardsort, nor are they guaranteed. Please keep that in mind.


Top
 Profile  
 
PostPosted: Tue Jan 24, 2017 7:55 pm 

Joined: Tue Sep 01, 2015 7:23 am
Posts: 125
What is a Dallas box? Should it be removed to increase value?


Top
 Profile  
 
PostPosted: Tue Jan 24, 2017 8:05 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3062
Location: Low DOS
The Dallas box is a battery and must be removed before sending in your order. They're socketed like standard ICs bit boardsort doesn't take them or anything containing them if attached on reception.

_________________
-- my grades are my own and do not represent an offer from boardsort, nor are they guaranteed. Please keep that in mind.


Top
 Profile  
 
PostPosted: Wed Jan 25, 2017 9:52 am 

Joined: Tue Sep 01, 2015 7:23 am
Posts: 125
Thank you Lostinlodos! Your generosity with your knowledge is a huge help and blessing! I will make sure to remove these.


Top
 Profile  
 
PostPosted: Wed Jan 25, 2017 7:39 pm 

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 3062
Location: Low DOS
By the way what's missing is the jumper pins for setting channels. This was an institution board. Settings are made on a prom and not the board for security.
Education, banking, or manufacturing were the common destinations.

Ctr shift F6 was the usual boot command to load the screen up.

_________________
-- my grades are my own and do not represent an offer from boardsort, nor are they guaranteed. Please keep that in mind.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 5 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: