Welcome to Boardsortâ„¢ - Learn - Sell - Profit -

Learn to properly Sort, Sell, and Profit from your electronic scrap material.
It is currently Fri Mar 29, 2024 2:26 am


Post new topic Reply to topic  [ 6 posts ] 
Author Message
PostPosted: Tue Oct 26, 2021 1:32 pm 

Joined: Mon Oct 25, 2021 12:03 pm
Posts: 12
I have 3 versions of Cellular uplink cards used in security systems
How would this card be classified? They are all 3 1/2 by 3 inches in size.

Attachment:
Pic_1.png
Pic_1.png [ 752.94 KiB | Viewed 1310 times ]


Attachment:
Pic_2.png
Pic_2.png [ 592.71 KiB | Viewed 1308 times ]


Attachment:
Pic_3.png
Pic_3.png [ 691.22 KiB | Viewed 1310 times ]


Top
 Profile  
 
PostPosted: Tue Oct 26, 2021 10:22 pm 

Joined: Thu Feb 04, 2021 2:53 am
Posts: 385
1. You will need to remove the two metal cylinders (not sure what they are, capacitors?). High peripheral
2. High peripheral
3. High peripheral

Also, I suggest you to upload photos as separate images instead of as collages


Top
 Profile  
 
PostPosted: Tue Oct 26, 2021 11:17 pm 

Joined: Sat Nov 29, 2014 9:44 pm
Posts: 1138
Location: I'm right here :D
Boardsort doesn't buy SIM cards at present so make sure you pull those out. Do remove the shields. Based on similar boards I've sent I would think 1 and 2 have a chance of going low telco if you remove the wire clamps. 3, I think you need to remove the wire clamps to get high peripheral.

_________________
Here to learn more so I can recycle more
My grades are my own opinion and not an official grade from Boardsort


Top
 Profile  
 
PostPosted: Wed Oct 27, 2021 10:59 am 

Joined: Mon Oct 25, 2021 12:03 pm
Posts: 12
Thank you for your input. As an example it would be best to submit the board from the first set of pictures as shown below.
I do have a question, if it is better to pull off the two Capacitors, SIM Chip and the wire connectors, should I leave the toggle switches on the board and the antenna connector?


Attachments:
20211027_094805.jpg
20211027_094805.jpg [ 453.82 KiB | Viewed 1255 times ]
20211027_095219.jpg
20211027_095219.jpg [ 452.56 KiB | Viewed 1255 times ]
Top
 Profile  
 
PostPosted: Wed Oct 27, 2021 3:59 pm 

Joined: Sat Nov 29, 2014 9:44 pm
Posts: 1138
Location: I'm right here :D
To your question, the toggle and antennae connector should stay.

Seeing the better photo, I think your definitely on the higher end of high peripheral for that particular board but I'm still not 100% it'll make low telco. If you have lots of that board to go through I'd just leave the extraneous material on and go high peripheral with them. Unless ccussins or someone can verify it making low telco of course.

_________________
Here to learn more so I can recycle more
My grades are my own opinion and not an official grade from Boardsort


Top
 Profile  
 
PostPosted: Wed Oct 27, 2021 6:36 pm 

Joined: Mon Oct 25, 2021 12:03 pm
Posts: 12
I have quite a few of these things and getting a few more everyday or so. It was pretty easy to remove the capacitors and wire attachments so if it would make low telco I would probably remove what ever was needed. Never sent anything into Boardsort before but I am thinking the shipping is not going to be cheap. Really appreciated your thoughts on these boards


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

cron