Welcome to Boardsort™ - Learn - Sell - Profit -

Learn to properly Sort, Sell, and Profit from your electronic scrap material.
It is currently Wed Nov 30, 2022 12:33 pm


Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: Please ID Group#2
PostPosted: Wed Sep 23, 2020 2:19 pm 

Joined: Tue Mar 19, 2019 4:41 pm
Posts: 87
Please ID Category. Board from Sony disc drive


Attachments:
File comment: Front/Back
IMG_2463.jpg
IMG_2463.jpg [ 1.4 MiB | Viewed 905 times ]
Top
 Profile  
 
 Post subject: Re: Please ID Group#2
PostPosted: Fri Sep 25, 2020 2:13 am 
Site Admin
User avatar

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 9508
Location: Low DOS
Floppy disk controller board
Peripheral

_________________
42 6F 61 72 64 73 6F 72 74 2E 63 6F 6D


Top
 Profile  
 
 Post subject: Re: Please ID Group#2
PostPosted: Tue Nov 22, 2022 10:14 pm 

Joined: Sun Jun 04, 2017 4:13 pm
Posts: 5
lostinlodos wrote:
Floppy disk controller board
Peripheral


Is it considered low peripheral or high peripheral?


Top
 Profile  
 
 Post subject: Re: Please ID Group#2
PostPosted: Tue Nov 22, 2022 10:32 pm 

Joined: Thu Aug 01, 2019 6:55 pm
Posts: 485
If pins are gold, high peripheral; if not, midgrade, possibly low peripheral.


Top
 Profile  
 
 Post subject: Re: Please ID Group#2
PostPosted: Wed Nov 23, 2022 12:07 am 
Site Admin
User avatar

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 9508
Location: Low DOS
If the pins are not gold I would expect low peripheral to be the class.

_________________
42 6F 61 72 64 73 6F 72 74 2E 63 6F 6D


Top
 Profile  
 
 Post subject: Re: Please ID Group#2
PostPosted: Wed Nov 23, 2022 9:01 pm 

Joined: Thu Aug 01, 2019 6:55 pm
Posts: 485
I wasn't completely sure so I said the lower of the two grades that they might fall under. At least before the split I think they went either low grade or midgrade.


Top
 Profile  
 
 Post subject: Re: Please ID Group#2
PostPosted: Thu Nov 24, 2022 7:05 am 
Site Admin
User avatar

Joined: Tue Feb 03, 2015 6:57 pm
Posts: 9508
Location: Low DOS
It’s good thinking.
The thing with floppy boards is the main 5 types of disk drive are fairly consistent. You have your single layer or dual layer controller chip, a few ASICs and the thick plate pins, or edge connector (gold fingers).
The value is nearly the same be it an 8” drive or a 3” drive.
About the only exception tin pins, and tin is expensive enough to guarantee you still get some level of peripheral.

_________________
42 6F 61 72 64 73 6F 72 74 2E 63 6F 6D


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: