Boardsort.com

Your complete E-scrap resource website. LEARN - SELL - PROFIT
It is currently Mon Oct 18, 2021 1:49 pm


Post new topic Reply to topic  [ 5 posts ] 
Author Message
 Post subject: ID Assist Request 1
PostPosted: Mon Sep 13, 2021 4:58 pm 

Joined: Mon Jun 13, 2016 10:38 am
Posts: 35
I have bulk of most of these but not sure of ID


Attachments:
IMG_2672.jpeg
IMG_2672.jpeg [ 1.86 MiB | Viewed 516 times ]
IMG_2671.jpeg
IMG_2671.jpeg [ 1.55 MiB | Viewed 516 times ]
IMG_2670.jpeg
IMG_2670.jpeg [ 1.84 MiB | Viewed 516 times ]
IMG_2669.jpeg
IMG_2669.jpeg [ 1.84 MiB | Viewed 516 times ]
IMG_2667.jpeg
IMG_2667.jpeg [ 2.17 MiB | Viewed 516 times ]
IMG_2666.jpeg
IMG_2666.jpeg [ 2.1 MiB | Viewed 516 times ]
IMG_2665.jpeg
IMG_2665.jpeg [ 1.87 MiB | Viewed 516 times ]
IMG_2664.jpeg
IMG_2664.jpeg [ 1.91 MiB | Viewed 516 times ]
Top
 Profile  
 
 Post subject: Re: ID Assist Request 1
PostPosted: Sun Sep 19, 2021 6:09 am 

Joined: Mon Sep 02, 2019 12:00 am
Posts: 145
You had asked in another post why no answers as to ID of these boards. While they appear to have gold pins and sufficient gold flash on posts, all components are either diodes or miniature. Most of us are familiar with the standard IC's and can make an accurate id based on that. But with the particular design of these, we don't see enough to evaluate. Some of these have the gold fingers, gold pins, and no excessive junk weight, so should go as high peripheral or better, but then it appears the board itself may be a drilled board, with no internal layers of conductive copper, so the board itself may lower the grade.
Since I hand deliver, I simply box the identical, label them as what I think, and let the dock crew put them in the official class at the receiving dock. If you are shipping, you don't have this option.


Top
 Profile  
 
 Post subject: Re: ID Assist Request 1
PostPosted: Sun Sep 19, 2021 11:34 pm 

Joined: Fri Oct 12, 2018 4:40 pm
Posts: 1120
Sorry for the delayed response. I have been busy the last few days.

1) High Grade Peripheral
2) Midgrade
3) Low Grade Peripheral
4) Low Grade Peripheral as is; if you cut/break off the blank section, it can go High Grade Peripheral.
5) High Grade Peripheral
6) High Grade Peripheral if you remove the component that has the number 9100-4858-1 on it.
7) High Grade Peripheral
8) High Grade Peripheral

Note: Make sure you remove all wires and cables from boards.

I will check with Chris on these boards to make sure I'm not completely wrong here.


Top
 Profile  
 
 Post subject: Re: ID Assist Request 1
PostPosted: Thu Sep 23, 2021 7:11 pm 

Joined: Mon Jun 13, 2016 10:38 am
Posts: 35
Thank you, very helpful!!


Top
 Profile  
 
 Post subject: Re: ID Assist Request 1
PostPosted: Fri Sep 24, 2021 2:25 pm 

Joined: Fri Oct 12, 2018 4:40 pm
Posts: 1120
Chris said:
Boardsort wrote:
All High Grade Peripheral except for board 2 which is Midgrade. You don't have to remove the blank section on board 4 as it can go High Grade Peripheral as is. You should remove the component mentioned on board 6 though.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 5 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: