Welcome to Boardsort™ - Learn - Sell - Profit -

Learn to properly Sort, Sell, and Profit from your electronic scrap material.
It is currently Mon Mar 16, 2026 4:41 pm

Board index » What is it? Identification Forum

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 1 of 2
  [ 12 posts ]  Go to page 1, 2  Next
  Previous topic | Next topic 
Author Message
Kevin349
 Post subject: Industrial charger
PostPosted: Sat Nov 15, 2025 10:28 am 

Joined: Sat Nov 15, 2025 10:20 am
Posts: 7
I have 30 to 40 industrial chargers I'm scrapping. Trying to see if the primary boards are worth anything. Thank you for the help.
Top
 Profile  
Reply with quote  
Kevin349
 Post subject: Re: Industrial charger
PostPosted: Sat Nov 15, 2025 10:39 am 

Joined: Sat Nov 15, 2025 10:20 am
Posts: 7
Front of circuit board


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
Reply with quote  
Kevin349
 Post subject: Re: Industrial charger
PostPosted: Sat Nov 15, 2025 10:41 am 

Joined: Sat Nov 15, 2025 10:20 am
Posts: 7
Back of circuit board


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
Reply with quote  
Spence1015
 Post subject: Re: Industrial charger
PostPosted: Sat Nov 15, 2025 2:26 pm 

Joined: Fri Dec 20, 2019 3:16 am
Posts: 455
Location: Ohio
Mid grade. I don't see much on the board that could take it to Low Per.

Make sure to take all ferrous metals and connector ends off the boards. Remove excess wires too. The screws, wire eyes, the clipped connectors, and data cord(ATA).
Top
 Profile  
Reply with quote  
Kevin349
 Post subject: Re: Industrial charger
PostPosted: Sat Nov 15, 2025 4:41 pm 

Joined: Sat Nov 15, 2025 10:20 am
Posts: 7
Thank you. At 50 cents a lb. It's probably not worth sending in. Thank you.
Top
 Profile  
Reply with quote  
kandroid96
 Post subject: Re: Industrial charger
PostPosted: Sat Nov 15, 2025 4:45 pm 

Joined: Wed Jan 13, 2021 9:48 pm
Posts: 48
Location: Upper Marlboro, MD
For this board to make sense in my book:

Take a jigsaw and cut the board in half. Use the white line as a divider. The top of the board moves on. The bottom board has no future here.

Next remove the remaining junk (Cut wire harnesses, large capacitors etc.)

You have what looks like 13 or 14 IC's and gold pins. I would classify what remains as HGP all day.

_________________
---
**Please keep in mind that my assessments on board quality are personal in nature

Abbreviations
HGT - High Grade Telecom
LGT - Low Grade Telecom
HGP - High Grade Peripherial
LGP - Low Grade Peripherial
MGB - Mid-Grade Board
LGB - Low-Grade Board
Top
 Profile  
Reply with quote  
Kevin349
 Post subject: Re: Industrial charger
PostPosted: Sat Nov 15, 2025 6:11 pm 

Joined: Sat Nov 15, 2025 10:20 am
Posts: 7
Fairly easy to split it. Does this look a little more valuable?


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
Reply with quote  
Spence1015
 Post subject: Re: Industrial charger
PostPosted: Tue Nov 18, 2025 12:57 am 

Joined: Fri Dec 20, 2019 3:16 am
Posts: 455
Location: Ohio
Looks good, see if you can carefully cut between this line here. It would look better and keep more components from falling off.

Attachment:
20251115_092222.jpg


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
Reply with quote  
Spence1015
 Post subject: Re: Industrial charger
PostPosted: Tue Nov 18, 2025 12:58 am 

Joined: Fri Dec 20, 2019 3:16 am
Posts: 455
Location: Ohio
Upgrade to Low Per
Top
 Profile  
Reply with quote  
Spence1015
 Post subject: Re: Industrial charger
PostPosted: Tue Nov 18, 2025 1:09 am 

Joined: Fri Dec 20, 2019 3:16 am
Posts: 455
Location: Ohio
Attachment:
20251115_092222.jpg


The circled areas are points you do not want to disturb. Keep them on. Try to carefully run that pink line I drew up.


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 12 posts ]  Go to page 1, 2  Next

Board index » What is it? Identification Forum

All times are UTC - 5 hours [ DST ]

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: